Network Working Group                                         R.  Braden
Request for Comments: 1071                                           ISI
                                                              D.  Borman
                                                           Cray Research
                                                            C. Partridge
                                                        BBN Laboratories
                                                          September 1988


                    Computing the Internet Checksum


Status of This Memo

   This memo summarizes techniques and algorithms for efficiently
   computing the Internet checksum.  It is not a standard, but a set of
   useful implementation techniques.  Distribution of this memo is
   unlimited.

1.  Introduction

   This memo discusses methods for efficiently computing the Internet
   checksum that is used by the standard Internet protocols IP, UDP, and
   TCP.

   An efficient checksum implementation is critical to good performance.
   As advances in implementation techniques streamline the rest of the
   protocol processing, the checksum computation becomes one of the
   limiting factors on TCP performance, for example.  It is usually
   appropriate to carefully hand-craft the checksum routine, exploiting
   every machine-dependent trick possible; a fraction of a microsecond
   per TCP data byte can add up to a significant CPU time savings
   overall.

   In outline, the Internet checksum algorithm is very simple:

   (1)  Adjacent octets to be checksummed are paired to form 16-bit
        integers, and the 1's complement sum of these 16-bit integers is
        formed.

   (2)  To generate a checksum, the checksum field itself is cleared,
        the 16-bit 1's complement sum is computed over the octets
        concerned, and the 1's complement of this sum is placed in the
        checksum field.

   (3)  To check a checksum, the 1's complement sum is computed over the
        same set of octets, including the checksum field.  If the result
        is all 1 bits (-0 in 1's complement arithmetic), the check
        succeeds.

        Suppose a checksum is to be computed over the sequence of octets



Braden, Borman, & Partridge                                     [Page 1]


RFC 1071            Computing the Internet Checksum       September 1988


        A, B, C, D, ... , Y, Z.  Using the notation [a,b] for the 16-bit
        integer a*256+b, where a and b are bytes, then the 16-bit 1's
        complement sum of these bytes is given by one of the following:

            [A,B] +' [C,D] +' ... +' [Y,Z]              [1]

            [A,B] +' [C,D] +' ... +' [Z,0]              [2]

        where +' indicates 1's complement addition. These cases
        correspond to an even or odd count of bytes, respectively.

        On a 2's complement machine, the 1's complement sum must be
        computed by means of an "end around carry", i.e., any overflows
        from the most significant bits are added into the least
        significant bits. See the examples below.

        Section 2 explores the properties of this checksum that may be
        exploited to speed its calculation.  Section 3 contains some
        numerical examples of the most important implementation
        techniques.  Finally, Section 4 includes examples of specific
        algorithms for a variety of common CPU types.  We are grateful
        to Van Jacobson and Charley Kline for their contribution of
        algorithms to this section.

        The properties of the Internet checksum were originally
        discussed by Bill Plummer in IEN-45, entitled "Checksum Function
        Design".  Since IEN-45 has not been widely available, we include
        it as an extended appendix to this RFC.

     2.  Calculating the Checksum

        This simple checksum has a number of wonderful mathematical
        properties that may be exploited to speed its calculation, as we
        will now discuss.


   (A)  Commutative and Associative

        As long as the even/odd assignment of bytes is respected, the
        sum can be done in any order, and it can be arbitrarily split
        into groups.

        For example, the sum [1] could be split into:

           ( [A,B] +' [C,D] +' ... +' [J,0] )

                  +' ( [0,K] +' ... +' [Y,Z] )               [3]







Braden, Borman, & Partridge                                     [Page 2]


RFC 1071            Computing the Internet Checksum       September 1988


   (B)  Byte Order Independence

        The sum of 16-bit integers can be computed in either byte order.
        Thus, if we calculate the swapped sum:

           [B,A] +' [D,C] +' ... +' [Z,Y]                   [4]

        the result is the same as [1], except the bytes are swapped in
        the sum! To see why this is so, observe that in both orders the
        carries are the same: from bit 15 to bit 0 and from bit 7 to bit
        8.  In other words, consistently swapping bytes simply rotates
        the bits within the sum, but does not affect their internal
        ordering.

        Therefore, the sum may be calculated in exactly the same way
        regardless of the byte order ("big-endian" or "little-endian")
        of the underlaying hardware.  For example, assume a "little-
        endian" machine summing data that is stored in memory in network
        ("big-endian") order.  Fetching each 16-bit word will swap
        bytes, resulting in the sum [4]; however, storing the result
        back into memory will swap the sum back into network byte order.

        Byte swapping may also be used explicitly to handle boundary
        alignment problems.  For example, the second group in [3] can be
        calculated without concern to its odd/even origin, as:

              [K,L] +' ... +' [Z,0]

        if this sum is byte-swapped before it is added to the first
        group.  See the example below.

   (C)  Parallel Summation

        On machines that have word-sizes that are multiples of 16 bits,
        it is possible to develop even more efficient implementations.
        Because addition is associative, we do not have to sum the
        integers in the order they appear in the message.  Instead we
        can add them in "parallel" by exploiting the larger word size.

        To compute the checksum in parallel, simply do a 1's complement
        addition of the message using the native word size of the
        machine.  For example, on a 32-bit machine we can add 4 bytes at
        a time: [A,B,C,D]+'... When the sum has been computed, we "fold"
        the long sum into 16 bits by adding the 16-bit segments.  Each
        16-bit addition may produce new end-around carries that must be
        added.

        Furthermore, again the byte order does not matter; we could
        instead sum 32-bit words: [D,C,B,A]+'... or [B,A,D,C]+'... and
        then swap the bytes of the final 16-bit sum as necessary.  See
        the examples below.  Any permutation is allowed that collects



Braden, Borman, & Partridge                                     [Page 3]


RFC 1071            Computing the Internet Checksum       September 1988


        all the even-numbered data bytes into one sum byte and the odd-
        numbered data bytes into the other sum byte.


   There are further coding techniques that can be exploited to speed up
   the checksum calculation.

   (1)  Deferred Carries

        Depending upon the machine, it may be more efficient to defer
        adding end-around carries until the main summation loop is
        finished.

        One approach is to sum 16-bit words in a 32-bit accumulator, so
        the overflows build up in the high-order 16 bits.  This approach
        typically avoids a carry-sensing instruction but requires twice
        as many additions as would adding 32-bit segments; which is
        faster depends upon the detailed hardware architecture.

   (2)  Unwinding Loops

        To reduce the loop overhead, it is often useful to "unwind" the
        inner sum loop, replicating a series of addition commands within
        one loop traversal.  This technique often provides significant
        savings, although it may complicate the logic of the program
        considerably.

   (3)  Combine with Data Copying

        Like checksumming, copying data from one memory location to
        another involves per-byte overhead.  In both cases, the
        bottleneck is essentially the memory bus, i.e., how fast the
        data can be fetched. On some machines (especially relatively
        slow and simple micro-computers), overhead can be significantly
        reduced by combining memory-to-memory copy and the checksumming,
        fetching the data only once for both.

   (4)  Incremental Update

        Finally, one can sometimes avoid recomputing the entire checksum
        when one header field is updated.  The best-known example is a
        gateway changing the TTL field in the IP header, but there are
        other examples (for example, when updating a source route).  In
        these cases it is possible to update the checksum without
        scanning the message or datagram.

        To update the checksum, simply add the differences of the
        sixteen bit integers that have been changed.  To see why this
        works, observe that every 16-bit integer has an additive inverse
        and that addition is associative.  From this it follows that
        given the original value m, the new value m', and the old



Braden, Borman, & Partridge                                     [Page 4]


RFC 1071            Computing the Internet Checksum       September 1988


        checksum C, the new checksum C' is:

                C' = C + (-m) + m' = C + (m' - m)


3. Numerical Examples

   We now present explicit examples of calculating a simple 1's
   complement sum on a 2's complement machine.  The examples show the
   same sum calculated byte by bye, by 16-bits words in normal and
   swapped order, and 32 bits at a time in 3 different orders.  All
   numbers are in hex.

                  Byte-by-byte    "Normal"  Swapped
                                    Order    Order

        Byte 0/1:    00   01        0001      0100
        Byte 2/3:    f2   03        f203      03f2
        Byte 4/5:    f4   f5        f4f5      f5f4
        Byte 6/7:    f6   f7        f6f7      f7f6
                    ---  ---       -----     -----
        Sum1:       2dc  1f0       2ddf0     1f2dc

                     dc   f0        ddf0      f2dc
        Carrys:       1    2           2         1
                     --   --        ----      ----
        Sum2:        dd   f2        ddf2      f2dd

        Final Swap:  dd   f2        ddf2      ddf2


        Byte 0/1/2/3:  0001f203     010003f2       03f20100
        Byte 4/5/6/7:  f4f5f6f7     f5f4f7f6       f7f6f5f4
                       --------     --------       --------
        Sum1:         0f4f7e8fa    0f6f4fbe8      0fbe8f6f4

        Carries:              0            0              0

        Top half:          f4f7         f6f4           fbe8
        Bottom half:       e8fa         fbe8           f6f4
                          -----        -----          -----
        Sum2:             1ddf1        1f2dc          1f2dc

                           ddf1         f2dc           f2dc
        Carrys:               1            1              1
                           ----         ----           ----
        Sum3:              ddf2         f2dd           f2dd

        Final Swap:        ddf2         ddf2           ddf2





Braden, Borman, & Partridge                                     [Page 5]


RFC 1071            Computing the Internet Checksum       September 1988


   Finally, here an example of breaking the sum into two groups, with
   the second group starting on a odd boundary:


                   Byte-by-byte    Normal
                                    Order

        Byte 0/1:    00   01        0001
        Byte 2/ :    f2  (00)       f200
                    ---  ---       -----
        Sum1:        f2   01        f201

        Byte 4/5:    03   f4        03f4
        Byte 6/7:    f5   f6        f5f6
        Byte 8/:     f7  (00)       f700
                    ---  ---       -----
        Sum2:                      1f0ea

        Sum2:                       f0ea
        Carry:                         1
                                   -----
        Sum3:                       f0eb

        Sum1:                       f201
        Sum3 byte swapped:          ebf0
                                   -----
        Sum4:                      1ddf1

        Sum4:                       ddf1
        Carry:                         1
                                   -----
        Sum5:                       ddf2






















Braden, Borman, & Partridge                                     [Page 6]


RFC 1071            Computing the Internet Checksum       September 1988


4.  Implementation Examples

   In this section we show examples of Internet checksum implementation
   algorithms that have been found to be efficient on a variety of
   CPU's.  In each case, we show the core of the algorithm, without
   including environmental code (e.g., subroutine linkages) or special-
   case code.

4.1  "C"

   The following "C" code algorithm computes the checksum with an inner
   loop that sums 16-bits at a time in a 32-bit accumulator.

   in 6
       {
           /* Compute Internet Checksum for "count" bytes
            *         beginning at location "addr".
            */
       register long sum = 0;

        while( count > 1 )  {
           /*  This is the inner loop */
               sum += * (unsigned short) addr++;
               count -= 2;
       }

           /*  Add left-over byte, if any */
       if( count > 0 )
               sum += * (unsigned char *) addr;

           /*  Fold 32-bit sum to 16 bits */
       while (sum>>16)
           sum = (sum & 0xffff) + (sum >> 16);

       checksum = ~sum;
   }


















Braden, Borman, & Partridge                                     [Page 7]


RFC 1071            Computing the Internet Checksum       September 1988


4.2  Motorola 68020

   The following algorithm is given in assembler language for a Motorola
   68020 chip.  This algorithm performs the sum 32 bits at a time, and
   unrolls the loop with 16 replications.  For clarity, we have omitted
   the logic to add the last fullword when the length is not a multiple
   of 4.  The result is left in register d0.

   With a 20MHz clock, this routine was measured at 134 usec/kB summing
   random data.  This algorithm was developed by Van Jacobson.


       movl    d1,d2
       lsrl    #6,d1       | count/64 = # loop traversals
       andl    #0x3c,d2    | Then find fractions of a chunk
       negl    d2
       andb    #0xf,cc     | Clear X (extended carry flag)

       jmp     pc@(2$-.-2:b,d2)  | Jump into loop

   1$:     | Begin inner loop...

       movl    a0@+,d2     |  Fetch 32-bit word
       addxl   d2,d0       |    Add word + previous carry
       movl    a0@+,d2     |  Fetch 32-bit word
       addxl   d2,d0       |    Add word + previous carry

           | ... 14 more replications
   2$:
       dbra    d1,1$   | (NB- dbra doesn't affect X)

       movl    d0,d1   | Fold 32 bit sum to 16 bits
       swap    d1      | (NB- swap doesn't affect X)
       addxw   d1,d0
       jcc     3$
       addw    #1,d0
   3$:
       andl    #0xffff,d0
















Braden, Borman, & Partridge                                     [Page 8]


RFC 1071            Computing the Internet Checksum       September 1988


4.3  Cray

   The following example, in assembler language for a Cray CPU, was
   contributed by Charley Kline.  It implements the checksum calculation
   as a vector operation, summing up to 512 bytes at a time with a basic
   summation unit of 32 bits.  This example omits many details having to
   do with short blocks, for clarity.

   Register A1 holds the address of a 512-byte block of memory to
   checksum.  First two copies of the data are loaded into two vector
   registers.  One is vector-shifted right 32 bits, while the other is
   vector-ANDed with a 32 bit mask. Then the two vectors are added
   together.  Since all these operations chain, it produces one result
   per clock cycle.  Then it collapses the result vector in a loop that
   adds each element to a scalar register.  Finally, the end-around
   carry is performed and the result is folded to 16-bits.

         EBM
         A0      A1
         VL      64            use full vectors
         S1      <32           form 32-bit mask from the right.
         A2      32
         V1      ,A0,1            load packet into V1
         V2      S1&V1            Form right-hand 32-bits in V2.
         V3      V1>A2            Form left-hand 32-bits in V3.
         V1      V2+V3            Add the two together.
         A2      63            Prepare to collapse into a scalar.
         S1      0
         S4      <16           Form 16-bit mask from the right.
         A4      16
   CK$LOOP S2    V1,A2
         A2      A2-1
         A0      A2
         S1      S1+S2
         JAN     CK$LOOP
         S2      S1&S4           Form right-hand 16-bits in S2
         S1      S1>A4           Form left-hand 16-bits in S1
         S1      S1+S2
         S2      S1&S4           Form right-hand 16-bits in S2
         S1      S1>A4           Form left-hand 16-bits in S1
         S1      S1+S2
         S1      #S1            Take one's complement
         CMR            At this point, S1 contains the checksum.











Braden, Borman, & Partridge                                     [Page 9]


RFC 1071            Computing the Internet Checksum       September 1988


4.4  IBM 370

   The following example, in assembler language for an IBM 370 CPU, sums
   the data 4 bytes at a time.  For clarity, we have omitted the logic
   to add the last fullword when the length is not a multiple of 4, and
   to reverse the bytes when necessary.  The result is left in register
   RCARRY.

   This code has been timed on an IBM 3090 CPU at 27 usec/KB when
   summing all one bits.  This time is reduced to 24.3 usec/KB if the
   trouble is taken to word-align the addends (requiring special cases
   at both the beginning and the end, and byte-swapping when necessary
   to compensate for starting on an odd byte).

   *      Registers RADDR and RCOUNT contain the address and length of
   *              the block to be checksummed.
   *
   *      (RCARRY, RSUM) must be an even/odd register pair.
   *      (RCOUNT, RMOD) must be an even/odd register pair.
   *
   CHECKSUM  SR    RSUM,RSUM       Clear working registers.
             SR    RCARRY,RCARRY
             LA    RONE,1          Set up constant 1.
   *
             SRDA  RCOUNT,6        Count/64 to RCOUNT.
             AR    RCOUNT,RONE       +1 = # times in loop.
             SRL   RMOD,26         Size of partial chunk to RMOD.
             AR    RADDR,R3        Adjust addr to compensate for
             S     RADDR,=F(64)      jumping into the loop.
             SRL   RMOD,1          (RMOD/4)*2 is halfword index.
             LH    RMOD,DOPEVEC9(RMOD) Use magic dope-vector for offset,
             B     LOOP(RMOD)          and jump into the loop...
   *
   *             Inner loop:
   *
   LOOP      AL    RSUM,0(,RADDR)   Add Logical fullword
             BC    12,*+6             Branch if no carry
             AR    RCARRY,RONE        Add 1 end-around
             AL    RSUM,4(,RADDR)   Add Logical fullword
             BC    12,*+6             Branch if no carry
             AR    RCARRY,RONE        Add 1 end-around
   *
   *                    ... 14 more replications ...
   *
             A     RADDR,=F'64'    Increment address ptr
             BCT   RCOUNT,LOOP     Branch on Count
    *
    *            Add Carries into sum, and fold to 16 bits
    *
             ALR   RCARRY,RSUM      Add SUM and CARRY words
             BC    12,*+6              and take care of carry



Braden, Borman, & Partridge                                    [Page 10]


RFC 1071            Computing the Internet Checksum       September 1988


             AR    RCARRY,RONE
             SRDL  RCARRY,16        Fold 32-bit sum into
             SRL   RSUM,16            16-bits
             ALR   RCARRY,RSUM
             C     RCARRY,=X'0000FFFF' and take care of any
             BNH   DONE                     last carry
             S     RCARRY,=X'0000FFFF'
   DONE      X     RCARRY,=X'0000FFFF' 1's complement














































Braden, Borman, & Partridge                                    [Page 11]


RFC 1071            Computing the Internet Checksum       September 1988


     IEN 45
     Section 2.4.4.5
















                       TCP Checksum Function Design



                            William W. Plummer


                       Bolt Beranek and Newman, Inc.
                             50 Moulton Street
                           Cambridge MA   02138


                                5 June 1978























Braden, Borman, & Partridge                                    [Page 12]


RFC 1071            Computing the Internet Checksum       September 1988


     Internet Experiment Note  45                          5 June 1978
     TCP Checksum Function Design                   William W. Plummer

     1.      Introduction

     Checksums  are  included  in  packets  in   order   that   errors
     encountered  during  transmission  may be detected.  For Internet
     protocols such as TCP [1,9] this is especially important  because
     packets  may  have  to cross wireless networks such as the Packet
     Radio Network  [2]  and  Atlantic  Satellite  Network  [3]  where
     packets  may  be  corrupted.  Internet protocols (e.g., those for
     real time speech transmission) can tolerate a  certain  level  of
     transmission  errors  and  forward error correction techniques or
     possibly no checksum at all might be better.  The focus  in  this
     paper  is  on  checksum functions for protocols such as TCP where
     the required reliable delivery is achieved by retransmission.

     Even if the checksum appears good on a  message  which  has  been
     received, the message may still contain an undetected error.  The
     probability of this is bounded by 2**(-C) where  C  is the number
     of  checksum bits.  Errors can arise from hardware (and software)
     malfunctions as well as transmission  errors.   Hardware  induced
     errors  are  usually manifested in certain well known ways and it
     is desirable to account for this in the design  of  the  checksum
     function.  Ideally no error of the "common hardware failure" type
     would go undetected.

     An  example  of  a  failure  that  the  current checksum function
     handles successfully is picking up a bit in the network interface
     (or I/O buss, memory channel, etc.).  This will always render the
     checksum bad.  For an example of  how  the  current  function  is
     inadequate, assume that a control signal stops functioning in the
     network  interface and the interface stores zeros in place of the
     real data.  These  "all  zero"  messages  appear  to  have  valid
     checksums.   Noise  on the "There's Your Bit" line of the ARPANET
     Interface [4] may go undetected because the extra bits input  may
     cause  the  checksum  to be perturbed (i.e., shifted) in the same
     way as the data was.

     Although messages containing undetected errors will  occasionally
     be  passed  to  higher levels of protocol, it is likely that they
     will not make sense at that level.  In the case of TCP most  such
     messages will be ignored, but some could cause a connection to be
     aborted.   Garbled  data could be viewed as a problem for a layer
     of protocol above TCP which itself may have a checksuming scheme.

     This paper is the first step in design of a new checksum function
     for TCP  and  some  other  Internet  protocols.   Several  useful
     properties  of  the current function are identified.  If possible

                                   - 1 -



Braden, Borman, & Partridge                                    [Page 13]


RFC 1071            Computing the Internet Checksum       September 1988


     Internet Experiment Note  45                          5 June 1978
     TCP Checksum Function Design                   William W. Plummer

     these should be retained  in  any  new  function.   A  number  of
     plausible  checksum  schemes are investigated.  Of these only the
     "product code" seems to be simple enough for consideration.

     2.      The Current TCP Checksum Function

     The current function is  oriented  towards  sixteen-bit  machines
     such  as  the PDP-11 but can be computed easily on other machines
     (e.g., PDP-10).  A packet is thought of as  a  string  of  16-bit
     bytes  and the checksum function is the one's complement sum (add
     with  end-around  carry)  of  those  bytes.   It  is  the   one's
     complement  of  this sum which is stored in the checksum field of
     the TCP header.  Before computing the checksum value, the  sender
     places  a  zero  in  the  checksum  field  of the packet.  If the
     checksum value computed by a receiver of the packet is zero,  the
     packet  is  assumed  to  be  valid.  This is a consequence of the
     "negative" number in the checksum field  exactly  cancelling  the
     contribution of the rest of the packet.

     Ignoring  the  difficulty  of  actually  evaluating  the checksum
     function for a given  packet,  the  way  of  using  the  checksum
     described  above  is quite simple, but it assumes some properties
     of the checksum operator (one's complement addition, "+" in  what
     follows):

       (P1)    +  is commutative.  Thus, the  order  in  which
             the   16-bit   bytes   are  "added"  together  is
             unimportant.

       (P2)    +  has  at  least  one  identity  element  (The
             current  function  has  two:  +0  and  -0).  This
             allows  the  sender  to  compute   the   checksum
             function by placing a zero in the packet checksum
             field before computing the value.

       (P3)    +  has an  inverse.   Thus,  the  receiver  may
             evaluate the checksum function and expect a zero.

       (P4)    +  is associative, allowing the checksum  field
             to be anywhere in the packet and the 16-bit bytes
             to be scanned sequentially.

     Mathematically, these properties of the binary operation "+" over
     the set of 16-bit numbers forms an Abelian group [5].  Of course,
     there  are  many Abelian groups but not all would be satisfactory
     for  use  as  checksum  operators.   (Another  operator   readily

                                   - 2 -



Braden, Borman, & Partridge                                    [Page 14]


RFC 1071            Computing the Internet Checksum       September 1988


     Internet Experiment Note  45                          5 June 1978
     TCP Checksum Function Design                   William W. Plummer

     available  in  the  PDP-11  instruction set that has all of these
     properties is exclusive-OR, but XOR is unsatisfactory  for  other
     reasons.)

     Albeit imprecise, another property which must be preserved in any
     future checksum scheme is:

       (P5)    +  is fast to compute on a variety of  machines
             with limited storage requirements.

     The  current  function  is  quite  good  in this respect.  On the
     PDP-11 the inner loop looks like:

             LOOP:   ADD (R1)+,R0    ; Add the next 16-bit byte
                     ADC R0          ; Make carry be end-around
                     SOB R2,LOOP     ; Loop over entire packet.

              ( 4 memory cycles per 16-bit byte )

     On the PDP-10 properties  P1-4  are  exploited  further  and  two
     16-bit bytes per loop are processed:

     LOOP: ILDB THIS,PTR   ; Get 2 16-bit bytes
           ADD SUM,THIS    ; Add into current sum
           JUMPGE SUM,CHKSU2  ; Jump if fewer than 8 carries
           LDB THIS,[POINT 20,SUM,19] ; Get left 16 and carries
           ANDI SUM,177777 ; Save just low 16 here
           ADD SUM,THIS    ; Fold in carries
     CHKSU2: SOJG COUNT,LOOP ; Loop over entire packet

     ( 3.1 memory cycles per 16-bit byte )

     The  "extra"  instruction  in  the  loops  above  are required to
     convert the two's complement  ADD  instruction(s)  into  a  one's
     complement  add  by  making  the  carries  be  end-around.  One's
     complement arithmetic is better than two's complement because  it
     is  equally  sensitive  to errors in all bit positions.  If two's
     complement addition were used, an even number  of  1's  could  be
     dropped  (or  picked  up)  in  the  most  significant bit channel
     without affecting the value of the checksum.   It  is  just  this
     property  that makes some sort of addition preferable to a simple
     exclusive-OR which is frequently used but permits an even  number
     of drops (pick ups) in any bit channel.  RIM10B paper tape format
     used  on PDP-10s [10] uses two's complement add because space for
     the loader program is extremely limited.

                                   - 3 -




Braden, Borman, & Partridge                                    [Page 15]


RFC 1071            Computing the Internet Checksum       September 1988


     Internet Experiment Note  45                          5 June 1978
     TCP Checksum Function Design                   William W. Plummer

     Another property of the current checksum scheme is:

       (P6)    Adding the checksum to a packet does not change
             the information bytes.  Peterson [6] calls this a
             "systematic" code.

     This property  allows  intermediate  computers  such  as  gateway
     machines  to  act  on  fields  (i.e.,  the  Internet  Destination
     Address) without having to first  decode  the  packet.   Cyclical
     Redundancy  Checks  used  for error correction are not systematic
     either.  However, most applications of  CRCs  tend  to  emphasize
     error  detection rather than correction and consequently can send
     the message unchanged, with the CRC check bits being appended  to
     the  end.   The  24-bit CRC used by ARPANET IMPs and Very Distant
     Host Interfaces [4] and the ANSI standards for 800 and 6250  bits
     per inch magnetic tapes (described in [11]) use this mode.

     Note  that  the  operation  of higher level protocols are not (by
     design) affected by anything that may be done by a gateway acting
     on possibly invalid packets.  It is permissible for  gateways  to
     validate  the  checksum  on  incoming  packets,  but  in  general
     gateways will not know how to  do  this  if  the  checksum  is  a
     protocol-specific feature.

     A final property of the current checksum scheme which is actually
     a consequence of P1 and P4 is:

       (P7)    The checksum may be incrementally modified.

     This  property permits an intermediate gateway to add information
     to a packet, for instance a timestamp, and "add"  an  appropriate
     change  to  the  checksum  field  of  the  packet.  Note that the
     checksum  will  still  be  end-to-end  since  it  was  not  fully
     recomputed.

     3.      Product Codes

     Certain  "product  codes"  are potentially useful for checksuming
     purposes.  The following is a brief description of product  codes
     in  the  context  of TCP.  More general treatment can be found in
     Avizienis [7] and probably other more recent works.

     The basic concept of this coding is that the message (packet)  to
     be sent is formed by transforming the original source message and
     adding  some  "check"  bits.   By  reading  this  and  applying a
     (possibly different) transformation, a receiver  can  reconstruct

                                   - 4 -



Braden, Borman, & Partridge                                    [Page 16]


RFC 1071            Computing the Internet Checksum       September 1988


     Internet Experiment Note  45                          5 June 1978
     TCP Checksum Function Design                   William W. Plummer

     the  original  message  and  determine  if  it has been corrupted
     during transmission.

              Mo              Ms              Mr

             -----           -----           -----
             | A |  code     | 7 |   decode  | A |
             | B |    ==>    | 1 |     ==>   | B |
             | C |           | 4 |           | C |
             -----           |...|           -----
                             | 2 | check     plus "valid" flag
                             ----- info

             Original        Sent            Reconstructed

     With product codes the transformation is  Ms = K * Mo .  That is,
     the message sent is simply the product of  the  original  message
     Mo   and  some  well known constant  K .  To decode, the received
     Ms  is divided by  K  which will yield  Mr  as the  quotient  and
     0   as the remainder if  Mr is to be considered the same as  Mo .

     The first problem is selecting a "good" value for  K, the  "check
     factor".   K  must  be  relatively  prime  to  the base chosen to
     express  the  message.   (Example:  Binary   messages   with    K
     incorrectly  chosen  to be 8.  This means that  Ms  looks exactly
     like  Mo  except that three zeros have been appended.   The  only
     way  the message could look bad to a receiver dividing by 8 is if
     the error occurred in one of those three bits.)

     For TCP the base  R  will be chosen to be 2**16.  That is,  every
     16-bit byte (word on the PDP-11) will be considered as a digit of
     a big number and that number is the message.  Thus,

                     Mo =  SIGMA [ Bi * (R**i)]   ,   Bi is i-th byte
                          i=0 to N

                     Ms = K * Mo

     Corrupting a single digit  of   Ms   will  yield   Ms' =  Ms +or-
     C*(R**j)  for some radix position  j .  The receiver will compute
     Ms'/K = Mo +or- C(R**j)/K. Since R  and  K  are relatively prime,
     C*(R**j) cannot be any exact  multiple  of   K.   Therefore,  the
     division will result in a non-zero remainder which indicates that
     Ms'   is  a  corrupted  version  of  Ms.  As will be seen, a good
     choice for  K  is (R**b - 1), for some  b  which  is  the  "check
     length"  which  controls  the  degree  of detection to be had for

                                   - 5 -



Braden, Borman, & Partridge                                    [Page 17]


RFC 1071            Computing the Internet Checksum       September 1988


     Internet Experiment Note  45                          5 June 1978
     TCP Checksum Function Design                   William W. Plummer

     burst errors which affect a string of digits (i.e., 16-bit bytes)
     in the message.  In fact  b  will be chosen to be  1, so  K  will
     be  2**16 - 1 so that arithmetic operations will be simple.  This
     means  that  all  bursts  of  15  or fewer bits will be detected.
     According to [7] this choice for  b   results  in  the  following
     expression for the fraction of undetected weight 2 errors:

      f =  16(k-1)/[32(16k-3) + (6/k)]  where k is the message length.

     For  large messages  f  approaches  3.125 per cent as  k  goes to
     infinity.

     Multiple precision multiplication and division are normally quite
     complex operations, especially on small machines which  typically
     lack  even  single precision multiply and divide operations.  The
     exception to this is exactly the case being dealt  with  here  --
     the  factor  is  2**16  - 1  on machines with a word length of 16
     bits.  The reason for this is due to the following identity:

             Q*(R**j)  =  Q, mod (R-1)     0 <= Q < R

     That is, any digit  Q  in the selected  radix  (0,  1,  ...  R-1)
     multiplied  by any power of the radix will have a remainder of  Q
     when divided by the radix minus 1.

     Example:  In decimal R = 10.  Pick  Q = 6.

                     6  =   0 * 9  +  6  =  6, mod 9
                    60  =   6 * 9  +  6  =  6, mod 9
                   600  =  66 * 9  +  6  =  6, mod 9   etc.

        More to the point, rem(31415/9) = rem((30000+1000+400+10+5)/9)
           = (3 mod 9) + (1 mod 9) + (4 mod 9) + (1 mod 9) + (5 mod 9)
           = (3+1+4+1+5) mod 9
           = 14 mod 9
           = 5

     So, the remainder of a number divided by the radix minus one  can
     be  found  by simply summing the digits of the number.  Since the
     radix in the TCP case has been chosen to be  2**16 and the  check
     factor is  2**16 - 1, a message can quickly be checked by summing
     all  of  the  16-bit  words  (on  a  PDP-11),  with carries being
     end-around.  If zero is the result, the message can be considered
     valid.  Thus, checking a product coded  message  is  exactly  the
     same complexity as with the current TCP checksum!

                                   - 6 -




Braden, Borman, & Partridge                                    [Page 18]


RFC 1071            Computing the Internet Checksum       September 1988


     Internet Experiment Note  45                          5 June 1978
     TCP Checksum Function Design                   William W. Plummer

     In  order  to  form   Ms,  the  sender must multiply the multiple
     precision "number"  Mo  by  2**16 - 1.  Or,  Ms = (2**16)Mo - Mo.
     This is performed by shifting  Mo   one  whole  word's  worth  of
     precision  and  subtracting   Mo.   Since  carries must propagate
     between digits, but it is only the  current  digit  which  is  of
     interest, one's complement arithmetic is used.

             (2**16)Mo =  Mo0 + Mo1 + Mo2 + ... + MoX +  0
                 -  Mo =    - ( Mo0 + Mo1 + ......... + MoX)
             ---------    ----------------------------------
                Ms     =  Ms0 + Ms1 + ...             - MoX

     A  loop  which  implements  this  function on a PDP-11 might look
     like:
             LOOP:   MOV -2(R2),R0   ; Next byte of (2**16)Mo
                     SBC R0          ; Propagate carries from last SUB
                     SUB (R2)+,R0    ; Subtract byte of  Mo
                     MOV R0,(R3)+    ; Store in Ms
                     SOB R1,LOOP     ; Loop over entire message
                                     ; 8 memory cycles per 16-bit byte

     Note that the coding procedure is not done in-place since  it  is
     not  systematic.   In general the original copy, Mo, will have to
     be  retained  by  the  sender  for  retransmission  purposes  and
     therefore  must  remain  readable.   Thus  the  MOV  R0,(R3)+  is
     required which accounts for 2 of the  8  memory cycles per  loop.

     The  coding  procedure  will  add  exactly one 16-bit word to the
     message since  Ms <  (2**16)Mo .  This additional 16 bits will be
     at the tail of the message, but may be  moved  into  the  defined
     location  in the TCP header immediately before transmission.  The
     receiver will have to undo this to put  Ms   back  into  standard
     format before decoding the message.

     The  code  in  the receiver for fully decoding the message may be
     inferred  by  observing  that  any  word  in   Ms   contains  the
     difference between two successive words of  Mo  minus the carries
     from the previous word, and the low order word contains minus the
     low word of Mo.  So the low order (i.e., rightmost) word of Mr is
     just  the negative of the low order byte of Ms.  The next word of
     Mr is the next word of  Ms  plus the just computed  word  of   Mr
     plus the carry from that previous computation.

     A  slight  refinement  of  the  procedure is required in order to
     protect against an all-zero message passing to  the  destination.
     This  will  appear to have a valid checksum because Ms'/K  =  0/K

                                   - 7 -



Braden, Borman, & Partridge                                    [Page 19]


RFC 1071            Computing the Internet Checksum       September 1988


     Internet Experiment Note  45                          5 June 1978
     TCP Checksum Function Design                   William W. Plummer

     = 0 with 0 remainder.  The refinement is to make  the  coding  be
     Ms  =  K*Mo + C where  C  is some arbitrary, well-known constant.
     Adding this constant requires a second pass over the message, but
     this will typically be very short since it can stop  as  soon  as
     carries  stop propagating.  Chosing  C = 1  is sufficient in most
     cases.

     The product code checksum must  be  evaluated  in  terms  of  the
     desired  properties  P1 - P7.  It has been shown that a factor of
     two more machine cycles are consumed in computing or verifying  a
     product code checksum (P5 satisfied?).

     Although the code is not systematic, the checksum can be verified
     quickly   without   decoding   the   message.   If  the  Internet
     Destination Address is located at the least  significant  end  of
     the packet (where the product code computation begins) then it is
     possible  for  a  gateway to decode only enough of the message to
     see this field without  having  to  decode  the  entire  message.
     Thus,   P6  is  at  least  partially  satisfied.   The  algebraic
     properties P1 through P4 are not  satisfied,  but  only  a  small
     amount  of  computation  is  needed  to  account  for this -- the
     message needs to be reformatted as previously mentioned.

     P7  is  satisfied  since  the  product  code  checksum   can   be
     incrementally  updated to account for an added word, although the
     procedure is  somewhat  involved.    Imagine  that  the  original
     message  has two halves, H1 and  H2.  Thus,  Mo = H1*(R**j) + H2.
     The timestamp word is to be inserted between these halves to form
     a modified  Mo' = H1*(R**(j+1)) + T*(R**j) + H2.  Since   K   has
     been  chosen to be  R-1, the transmitted message  Ms' = Mo'(R-1).
     Then,

      Ms' =  Ms*R + T(R-1)(R**j) + P2((R-1)**2)

          =  Ms*R + T*(R**(j+1))  + T*(R**j) + P2*(R**2) - 2*P2*R - P2

     Recalling that  R   is  2**16,  the  word  size  on  the  PDP-11,
     multiplying  by   R   means copying down one word in memory.  So,
     the first term of  Ms' is simply the  unmodified  message  copied
     down  one word.  The next term is the new data  T  added into the
     Ms' being formed beginning at the (j+1)th word.  The addition  is
     fairly  easy  here  since  after adding in T  all that is left is
     propagating the carry, and that can stop as soon as no  carry  is
     produced.  The other terms can be handle similarly.

                                   - 8 -





Braden, Borman, & Partridge                                    [Page 20]


RFC 1071            Computing the Internet Checksum       September 1988


     Internet Experiment Note  45                          5 June 1978
     TCP Checksum Function Design                   William W. Plummer

     4.      More Complicated Codes

     There exists a wealth of theory on error detecting and correcting
     codes.   Peterson  [6]  is an excellent reference.  Most of these
     "CRC" schemes are  designed  to  be  implemented  using  a  shift
     register  with  a  feedback  network  composed  of exclusive-ORs.
     Simulating such a logic circuit with a program would be too  slow
     to be useful unless some programming trick is discovered.

     One  such  trick has been proposed by Kirstein [8].  Basically, a
     few bits (four or eight) of the current shift register state  are
     combined with bits from the input stream (from Mo) and the result
     is  used  as  an  index  to  a  table  which yields the new shift
     register state and, if the code is not systematic, bits  for  the
     output  stream  (Ms).  A trial coding of an especially "good" CRC
     function using four-bit bytes showed showed this technique to  be
     about  four times as slow as the current checksum function.  This
     was true for  both  the  PDP-10  and  PDP-11  machines.   Of  the
     desirable  properties  listed  above, CRC schemes satisfy only P3
     (It has an inverse.), and P6 (It is systematic.).   Placement  of
     the  checksum  field in the packet is critical and the CRC cannot
     be incrementally modified.

     Although the bulk of coding theory deals with binary codes,  most
     of  the theory works if the alphabet contains   q  symbols, where
     q is a power of a prime number.  For instance  q  taken as  2**16
     should  make  a great deal of the theory useful on a word-by-word
     basis.

     5.      Outboard Processing

     When a function such as computing an involved  checksum  requires
     extensive processing, one solution is to put that processing into
     an  outboard processor.  In this way "encode message" and "decode
     message" become single instructions which do  not  tax  the  main
     host   processor.   The  Digital  Equipment  Corporation  VAX/780
     computer is equipped with special  hardware  for  generating  and
     checking  CRCs [13].  In general this is not a very good solution
     since such a processor must be constructed  for  every  different
     host machine which uses TCP messages.

     It is conceivable that the gateway functions for a large host may
     be  performed  entirely  in an "Internet Frontend Machine".  This
     machine would be  responsible  for  forwarding  packets  received

                                   - 9 -





Braden, Borman, & Partridge                                    [Page 21]


RFC 1071            Computing the Internet Checksum       September 1988


     Internet Experiment Note  45                          5 June 1978
     TCP Checksum Function Design                   William W. Plummer

     either  from the network(s) or from the Internet protocol modules
     in the connected host, and for  reassembling  Internet  fragments
     into  segments and passing these to the host.  Another capability
     of this machine would be  to  check  the  checksum  so  that  the
     segments given to the host are known to be valid at the time they
     leave the frontend.  Since computer cycles are assumed to be both
     inexpensive and available in the frontend, this seems reasonable.

     The problem with attempting to validate checksums in the frontend
     is that it destroys the end-to-end character of the checksum.  If
     anything,  this is the most powerful feature of the TCP checksum!
     There is a way to make the host-to-frontend link  be  covered  by
     the  end-to-end  checksum.   A  separate,  small protocol must be
     developed to cover this link.  After having validated an incoming
     packet from the network, the frontend would pass it to  the  host
     saying "here is an Internet segment for you.  Call it #123".  The
     host  would  save  this  segment,  and  send  a  copy back to the
     frontend saying, "Here is what you gave me as #123.  Is it  OK?".
     The  frontend  would  then  do a word-by-word comparison with the
     first transmission, and  tell  the  host  either  "Here  is  #123
     again",  or "You did indeed receive #123 properly.  Release it to
     the appropriate module for further processing."

     The headers on the messages crossing the host-frontend link would
     most likely be covered  by  a  fairly  strong  checksum  so  that
     information  like  which  function  is  being  performed  and the
     message reference numbers are reliable.  These headers  would  be
     quite  short,  maybe  only sixteen bits, so the checksum could be
     quite strong.  The bulk of the message would not be checksumed of
     course.
     The reason this scheme reduces the computing burden on  the  host
     is  that  all  that  is required in order to validate the message
     using the end-to-end checksum is to send it back to the  frontend
     machine.   In  the  case  of  the PDP-10, this requires only  0.5
     memory cycles per 16-bit byte of Internet message, and only a few
     processor cycles to setup the required transfers.

     6.      Conclusions

     There is an ordering of checksum functions: first and simplest is
     none at all which provides  no  error  detection  or  correction.
     Second,  is  sending a constant which is checked by the receiver.
     This also is extremely weak.  Third, the exclusive-OR of the data
     may be sent.  XOR takes the minimal amount of  computer  time  to
     generate  and  check,  but  is  not  a  good  checksum.   A two's
     complement sum of the data is somewhat better and takes  no  more

                                  - 10 -



Braden, Borman, & Partridge                                    [Page 22]


RFC 1071            Computing the Internet Checksum       September 1988


     Internet Experiment Note  45                          5 June 1978
     TCP Checksum Function Design                   William W. Plummer

     computer  time  to  compute.   Fifth, is the one's complement sum
     which is what is currently used by  TCP.   It  is  slightly  more
     expensive  in terms of computer time.  The next step is a product
     code.  The product code is strongly related to  one's  complement
     sum,  takes  still more computer time to use, provides a bit more
     protection  against  common  hardware  failures,  but  has   some
     objectionable properties.  Next is a genuine CRC polynomial code,
     used  for  checking  purposes only.  This is very expensive for a
     program to implement.  Finally, a full CRC error  correcting  and
     detecting scheme may be used.

     For  TCP  and  Internet  applications  the product code scheme is
     viable.  It suffers mainly in that messages  must  be  (at  least
     partially)  decoded  by  intermediate gateways in order that they
     can be forwarded.  Should product  codes  not  be  chosen  as  an
     improved  checksum,  some  slight  modification  to  the existing
     scheme might be possible.  For  instance  the  "add  and  rotate"
     function  used  for  paper  tape  by  the  PDP-6/10  group at the
     Artificial Intelligence Laboratory at  M.I.T.  Project  MAC  [12]
     could  be  useful  if it can be proved that it is better than the
     current scheme and that it  can  be  computed  efficiently  on  a
     variety of machines.





















                                  - 11 -







Braden, Borman, & Partridge                                    [Page 23]


RFC 1071            Computing the Internet Checksum       September 1988


     Internet Experiment Note  45                          5 June 1978
     TCP Checksum Function Design                   William W. Plummer

     References

     [1]  Cerf, V.G. and Kahn, Robert E., "A Protocol for Packet Network
          Communications," IEEE Transactions on Communications, vol.
          COM-22, No.  5, May 1974.

     [2]  Kahn, Robert E., "The Organization of Computer Resources into
          a Packet Radio Network", IEEE Transactions on Communications,
          vol. COM-25, no. 1, pp. 169-178, January 1977.

     [3]  Jacobs, Irwin, et al., "CPODA - A Demand Assignment Protocol
          for SatNet", Fifth Data Communications Symposium, September
          27-9, 1977, Snowbird, Utah

     [4]  Bolt Beranek and Newman, Inc.  "Specifications for the
          Interconnection of a Host and an IMP", Report 1822, January
          1976 edition.

     [5]  Dean, Richard A., "Elements of Abstract Algebra", John Wyley
          and Sons, Inc., 1966

     [6]  Peterson, W. Wesley, "Error Correcting Codes", M.I.T. Press
          Cambridge MA, 4th edition, 1968.

     [7]  Avizienis, Algirdas, "A Study of the Effectiveness of Fault-
          Detecting Codes for Binary Arithmetic", Jet Propulsion
          Laboratory Technical Report No. 32-711, September 1, 1965.

     [8]  Kirstein, Peter, private communication

     [9]  Cerf, V. G. and Postel, Jonathan B., "Specification of
          Internetwork Transmission Control Program Version 3",
          University of Southern California Information Sciences
          Institute, January 1978.

     [10] Digital Equipment Corporation, "PDP-10 Reference Handbook",
          1970, pp. 114-5.

     [11] Swanson, Robert, "Understanding Cyclic Redundancy Codes",
          Computer Design, November, 1975, pp. 93-99.

     [12] Clements, Robert C., private communication.

     [13] Conklin, Peter F., and Rodgers, David P., "Advanced
          Minicomputer Designed by Team Evaluation of Hardware/Software
          Tradeoffs", Computer Design, April 1978, pp. 136-7.

                                       - 12 -



Braden, Borman, & Partridge                                    [Page 24]