wdiff rfc6951.original rfc6951.txt

Network Working Group
Internet Engineering Task Force (IETF) M. Tuexen
Internet-Draft
Request for Comments: 6951 Muenster Univ. of Appl. Sciences
Intended status:
Category: Standards Track R. R. Stewart
Expires: September 20, 2013
ISSN: 2070-1721 Adara Networks
March 19,
April 2013

UDP Encapsulation of SCTP Stream Control Transmission Protocol (SCTP) Packets
for End-Host to End-Host Communication
draft-ietf-tsvwg-sctp-udp-encaps-14.txt

Abstract

This document describes a simple method of encapsulating SCTP Packets Stream
Control Transmission Protocol (SCTP) packets into UDP packets and its
limitations. This allows the usage of SCTP in networks with legacy NAT
NATs that do not supporting support SCTP. It can also be used to implement SCTP
on hosts without directly accessing the IP-layer, IP layer, for example example,
implementing it as part of the application without requiring special
privileges.

Please note that this document only describes the functionality
required within an SCTP stack to add on UDP encapsulation, providing
only those mechanisms for two end-hosts to communicate with each
other over UDP ports. In particular, it does not provide mechanisms
to determine whether UDP encapsulation is being used by the peer, nor
the mechanisms for determining which remote UDP port number can be
used. These functions are are out of scope for this document.

This document covers only end-hosts and not tunneling (egress or
ingress) end-points. endpoints.

Status of This Memo

This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents an Internet Standards Track document.

This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for a maximum publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of six months RFC 5741.

Information about the current status of this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

This Internet-Draft will expire on September 20, 2013.
http://www.rfc-editor.org/info/rfc6951.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2
2. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Use Cases . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.1. Portable SCTP Implementations . . . . . . . . . . . . . . 3
3.2. Legacy NAT Traversal . . . . . . . . . . . . . . . . . . 4
4. Unilateral Self-Address Fixing (UNSAF) Considerations . . . . 4
5. SCTP over UDP . . . . . . . . . . . . . . . . . . . . . . . . 4
5.1. Architectural Considerations . . . . . . . . . . . . . . 4
5.2. Packet Format . . . . . . . . . . . . . . . . . . . . . . 5
5.3. Encapsulation Procedure . . . . . . . . . . . . . . . . . 6
5.4. Decapsulation Procedure . . . . . . . . . . . . . . . . . 7 6
5.5. ICMP Considerations . . . . . . . . . . . . . . . . . . . 7
5.6. Path MTU Considerations . . . . . . . . . . . . . . . . . 8 7
5.7. Handling of Embedded IP-addresses IP Addresses . . . . . . . . . . . . 8
5.8. ECN Explicit Congestion Notification (ECN) Considerations . . . . . . . . . . . . . . . . . . . 8
6. Socket API Considerations . . . . . . . . . . . . . . . . . . 8
6.1. Get or Set the Remote UDP Encapsulation Port Number
(SCTP_REMOTE_UDP_ENCAPS_PORT) . . . . . . . . . . . . . . 9
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9
8. Security Considerations . . . . . . . . . . . . . . . . . . . 9
9. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 10
10. References . . . . . . . . . . . . . . . . . . . . . . . . . 10
10.1. Normative References . . . . . . . . . . . . . . . . . . 10
10.2. Informative References . . . . . . . . . . . . . . . . . 11
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 11

1. Introduction

This document describes a simple method of encapsulating SCTP packets
into UDP packets. SCTP SCTP, as defined in [RFC4960] [RFC4960], runs directly over
IPv4 or IPv6. There are two main reasons for encapsulating SCTP
packets:

o Allow To allow SCTP traffic to pass through legacy NATs, which do not
provide native SCTP support as specified in
[I-D.ietf-behave-sctpnat] [BEHAVE] and [I-D.ietf-tsvwg-natsupp].
[NATSUPP].

o Allow To allow SCTP to be implemented on hosts which that do not provide
direct access to the IP-layer. IP layer. In particular, applications can
use their own SCTP implementation if the operating system does not
provide one.

SCTP provides the necessary congestion control and reliability
service that UDP does not perform.

2. Conventions

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].

3. Use Cases

This section discusses two important use cases for encapsulating SCTP
into UDP.

3.1. Portable SCTP Implementations

Some operating systems support SCTP natively. For other operating
systems
systems, implementations are available, available but require special privileges
to install and/or use them. In some cases no cases, a kernel implementation
might not be available at all. When providing an SCTP implementation
as part of a user process, most operating systems require special
privileges to access the IP layer directly.

Using UDP encapsulation makes it possible to provide an SCTP
implementation as part of a user process which that does not require any
special privileges.

A crucial point for implementing SCTP in user space is that the
source address of outgoing packets needs to be controlled. This is
not an issue if the SCTP stack can use all addresses configured at
the IP-layer IP layer as source addresses. However, it is an issue when also
using the address management required for NAT traversal, described in
Section 5.7.

3.2. Legacy NAT Traversal

Using UDP encapsulation allows SCTP communication when traversing
legacy NATs (i.e (i.e, those NATs not supporting SCTP as described in
[I-D.ietf-behave-sctpnat]
[BEHAVE] and [I-D.ietf-tsvwg-natsupp]). [NATSUPP]). For single-
homed associations single-homed associations, IP addresses
MUST NOT be listed in the INIT and INIT-ACK chunks. To use multiple
addresses, the dynamic address reconfiguration extension described in
[RFC5061] MUST be used only with wildcard addresses in the ASCONF
chunks (Address Configuration Change Chunks) in combination with
[RFC4895].

For multi-homed multihomed SCTP association associations, the address management as described
in Section 5.7 MUST be performed.

SCTP sends periodic HEARTBEAT chunks on all idle paths. These can
keep the NAT state alive.

4. Unilateral Self-Address Fixing (UNSAF) Considerations

As [RFC3424] requires a limited scope, this document only covers SCTP
end-points
endpoints dealing with legacy constraints as described in Section 3.
It doesn't cover generic tunneling end-points. endpoints.

Obviously, the exit strategy is to use hosts supporting SCTP natively
and middleboxes supporting SCTP as specified in
[I-D.ietf-behave-sctpnat] [BEHAVE] and [I-D.ietf-tsvwg-natsupp]).
[NATSUPP].

5. SCTP over UDP

5.1. Architectural Considerations

UDP encapsulated

UDP-encapsulated SCTP is normally communicated between SCTP stacks
using the IANA-assigned UDP port number 9899 (sctp-tunneling) on both
ends. There are circumstances where other ports may be used on
either end: As stated earlier, implementations in the application
space might be required to use ports other than the registered port.
Since NAT boxes might change UDP port numbers, the receiver might
observe other UDP port numbers than were used by the sender.
Discovery of alternate ports is outside of the scope of this
document, but this section describes considerations for SCTP stack
design in light of their potential use.

Each SCTP stack uses a single local UDP encapsulation port number as
the destination port for all its incoming SCTP packets. While the
uniqueness of the local UDP encapsulation port number is not
necessarily required for the protocol, this greatly simplifies
implementation design, since different ports for each address would
require a sender implementation to choose the appropriate port while
doing source address selection. Using a single local UDP
encapsulation port number per host is not possible if the SCTP stack
is implemented as part of each application, there are multiple
applications, and some of the applications want to use the same IP- IP
address.

An SCTP implementation supporting UDP encapsulation MUST maintain a
remote UDP encapsulation port number per destination address for each
SCTP association. Again, because the remote stack may be using ports
other than the well-known port, each port may be different from each stack,
but
stack. However, because of remapping of ports by NATs, the remote
ports associated with different remote IP addresses may not be
identical, even if they are associated with the same stack.

Implementation note: Because the well-known port might not be used,
implementations need to allow other port numbers to be specified as a
local or remote UDP encapsulation port number through APIs.

5.2. Packet Format

To encapsulate an SCTP packet, a UDP header as defined in [RFC0768]
is inserted between the IP header as defined in [RFC0791] and the
SCTP common header as defined in [RFC4960].

Figure 1 shows the packet format of an encapsulated SCTP packet when
IPv4 is used.

0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv4 Header |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| UDP Header |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SCTP Common Header |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SCTP Chunk #1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SCTP Chunk #n |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Figure 1: An SCTP/UDP/IPv4 packet Packet

The packet format for an encapsulated SCTP packet when using IPv6 as
defined in [RFC2460] is shown in Figure 2. Please note the that the
number m of IPv6 extension headers can be 0.

0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 Base Header |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 Extension Header #1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 Extension Header #m |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| UDP Header |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SCTP Common Header |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SCTP Chunk #1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SCTP Chunk #n |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Figure 2: An SCTP/UDP/IPv6 packet Packet

5.3. Encapsulation Procedure

Within the UDP header, the source port MUST be the local UDP
encapsulation port number of the SCTP stack, and the destination port
MUST be the remote UDP encapsulation port number maintained for the
association and the destination address to which the packet is sent
(see Section 5.1).

Because the SCTP packet is the UDP payload, the length of the UDP
packet MUST be the length of the SCTP packet plus the size of the UDP
header.

The SCTP checksum MUST be computed for IPv4 and IPv6, and the UDP
checksum SHOULD be computed for IPv4 (see [RFC0768]) and IPv6 (see IPv6. (See [RFC0768]
regarding IPv4; see [RFC2460] and
[I-D.ietf-6man-udpzero]). [RFC6936] regarding IPv6.)
Although UDP with a zero checksum over IPv6 is allowed under certain
constraints [I-D.ietf-6man-udpzero], [RFC6936], this document does not specify mechanisms for
this mode. Deployed support may be limited and limited; also, at the time of
writing, the use of a zero UDP checksum would also be counter to the goal
of legacy NAT traversal.

5.4. Decapsulation Procedure
When an encapsulated packet is received, the UDP header is removed.
Then
Then, the generic lookup is performed, as done by an SCTP stack
whenever a packet is received, to find the association for the
received SCTP packet. After finding the SCTP association (which
includes checking the verification tag), the UDP source port MUST be
stored as the encapsulation port for the destination address the SCTP
packet is received from (see Section 5.1).

When a non-encapsulated SCTP packet is received by the SCTP stack,
the encapsulation of outgoing packets belonging to the same
association and the corresponding destination address MUST be
disabled.

5.5. ICMP Considerations

When receiving ICMP or ICMPv6 response packets, there might not be
enough bytes in the payload to identify the SCTP association which that the
SCTP packet triggering the ICMP or ICMPv6 packet belongs to. If a
received ICMP or ICMPv6 packet can not cannot be related to a specific SCTP
association or the verification tag can't cannot be verified, it MUST be
discarded silently. This In particular, this means in particular that the SCTP stack
MUST NOT rely on receiving ICMP or ICMPv6 messages. Implementation
constraints could prevent processing received ICMP or ICMPv6
messages.

If received ICMP or ICMPv6 messages are processed, the following
mapping SHOULD apply:

1. ICMP messages with type 'Destination Unreachable' and code 'Port
Unreachable' SHOULD be treated as ICMP messages with type
'Protocol
'Destination Unreachable' and code 'Destination Port unreachable. 'Protocol Unreachable'. See
[RFC0792] for more details.

2. ICMPv6 messages with type 'Destination Unreachable' and code
'Port unreachable' Unreachable' SHOULD be treated as ICMPv6 messages with type
'Parameter Problem' and code 'Unrecognized 'unrecognized Next Header type
encountered'. See [RFC4443] for more details.

5.6. Path MTU Considerations

If an SCTP endpoint starts to encapsulate the packets of a path, it
MUST decrease the Path MTU of that path by the size of the UDP
header. If it stops encapsulating them, the Path MTU SHOULD be
increased by the size of the UDP header.

When performing Path MTU discovery as described in [RFC4820] and
[RFC4821]
[RFC4821], it MUST be taken into account that one cannot rely on the
feedback provided by ICMP or ICMPv6 due to the limitation laid out in
Section 5.5.

If the implementation does not allow control of the don't fragment
(DF)-bit Don't Fragment
(DF) bit contained in the IPv4 header, then Path MTU discovery can't
be used. In this case, an implementation specific implementation-specific value should be
used instead.

5.7. Handling of Embedded IP-addresses IP Addresses

When using UDP encapsulation for legacy NAT traversal, IP addresses
that might require translation MUST NOT be put into any SCTP packet.

This means that a multi homed multihomed SCTP association is setup set up initially as
a singled homed one single-homed one, and the protocol extension [RFC5061] in
combination with [RFC4895] is used to add the other addresses. Only
wildcard addresses are put into the SCTP packet.

When addresses are changed during the lifetime of an association
[RFC5061] MUST be used with wildcard addresses only. If an SCTP end-
point
endpoint receives an ABORT with the T-bit set, it MAY use this as an
indication that the addresses seen by the peer might have changed.

5.8. ECN Explicit Congestion Notification (ECN) Considerations

If the implementation supports the sending and receiving of the ECN
bits for the IP protocols being used by an SCTP association, the ECN
bits MUST NOT be changed during sending and receiving.

6. Socket API Considerations

This section describes how the socket API defined in [RFC6458] needs
to be extended to provide a way for the application to control the
UDP encapsulation.

Please note that this section is informational only.

A socket API implementation based on [RFC6458] is extended by
supporting one new read/write socket option.

6.1. Get or Set the Remote UDP Encapsulation Port Number
(SCTP_REMOTE_UDP_ENCAPS_PORT)

This socket option can be used to set and retrieve the UDP
encapsulation port number. This allows an endpoint to encapsulate
initial packets.

struct sctp_udpencaps {
sctp_assoc_t sue_assoc_id;
struct sockaddr_storage sue_address;
uint16_t sue_port;
};

sue_assoc_id: This parameter is ignored for one-to-one style
sockets. For one-to-many style sockets sockets, the application may fill
in an association identifier or SCTP_FUTURE_ASSOC for this query.
It is an error to use SCTP_{CURRENT|ALL}_ASSOC in sue_assoc_id.

sue_address: This specifies which address is of interest. If a
wildcard address is provided provided, it applies only to future paths.

sue_port: The UDP port number in network byte order order; used as the
destination port number for UDP encapsulation. Providing a value
of 0 disables UDP encapsulation.

7. IANA Considerations

This document refers to the already assigned UDP port 9899 (sctp-
tunneling). IANA is requested to update has updated this assignment to refer to this
document. As per [RFC6335] [RFC6335], the Assignee should be is [IESG] and the Contact should be
is [IETF_Chair].

Please note that the TCP port 9899 (sctp-tunneling) assignment is not
needed anymore anymore, and IANA is asked to remove has removed this TCP port number
assignment. assignment
and marked TCP port 9899 as "Reserved".

8. Security Considerations

Encapsulating SCTP into UDP does not add any additional security
considerations to the ones given in [RFC4960] and [RFC5061].

Firewalls inspecting SCTP packets must also be aware of the
encapsulation and apply corresponding rules to the encapsulated
packets.

An attacker might send a malicious UDP packet towards an SCTP end-
point
endpoint to change the encapsulation port for a single remote address
of a particular SCTP association. However, as specified in
Section 5.4, this requires the usage of one of the two negotiated
verification tags. This protects against blind attackers the same
way as described in [RFC4960] for SCTP over IPv4 or IPv6. Non-blind
attackers can affect SCTP association using the UDP encapsulation
described in this document in the same way as SCTP associations not
using the UDP encapsulation of SCTP described here.

9. Acknowledgments

The authors wish to thank Stewart Bryant, Dave Crocker, Gorry
Fairhurst, Tero Kivinen, Barry Leiba, Pete Resnick, Martin
Stiemerling, Irene Ruengeler, and Dan Wing for their invaluable
comments.

10. References

10.1. Normative References

[RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768,
August 1980.

[RFC0791] Postel, J., "Internet Protocol", STD 5, RFC 791, September
1981.

[RFC0792] Postel, J., "Internet Control Message Protocol", STD 5,
RFC 792, September 1981.

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.

[RFC2460] Deering, S.E. and R.M. Hinden, "Internet Protocol, Version
6 (IPv6) Specification", RFC 2460, December 1998.

[RFC4443] Conta, A., Deering, S., and M. Gupta, "Internet Control
Message Protocol (ICMPv6) for the Internet Protocol
Version 6 (IPv6) Specification", RFC 4443, March 2006.

[RFC4820] Tuexen, M., Stewart, R., and P. Lei, "Padding Chunk and
Parameter for the Stream Control Transmission Protocol
(SCTP)", RFC 4820, March 2007.

[RFC4821] Mathis, M. and J. Heffner, "Packetization Layer Path MTU
Discovery", RFC 4821, March 2007.

[RFC4895] Tuexen, M., Stewart, R., Lei, P., and E. Rescorla,
"Authenticated Chunks for the Stream Control Transmission
Protocol (SCTP)", RFC 4895, August 2007.

[RFC4960] Stewart, R., "Stream Control Transmission Protocol", RFC
4960, September 2007.

[RFC5061] Stewart, R., Xie, Q., Tuexen, M., Maruyama, S., and M.
Kozuka, "Stream Control Transmission Protocol (SCTP)
Dynamic Address Reconfiguration", RFC 5061, September
2007.

10.2. Informative References

[BEHAVE] Stewart, R., Tuexen, M., and I. Ruengeler, "Stream Control
Transmission Protocol (SCTP) Network Address Translation",
Work in Progress, February 2013.

[NATSUPP] Stewart, R., Tuexen, M., and I. Ruengeler, "Stream Control
Transmission Protocol (SCTP) Network Address Translation
Support", Work in Progress, February 2013.

[RFC3424] Daigle, L. IAB, "IAB Considerations for UNilateral Self-
Address Fixing (UNSAF) Across Network Address
Translation", RFC 3424, November 2002.

[RFC6335] Cotton, M., Eggert, L., Touch, J., Westerlund, M., and S.
Cheshire, "Internet Assigned Numbers Authority (IANA)
Procedures for the Management of the Service Name and
Transport Protocol Port Number Registry", BCP 165, RFC
6335, August 2011.

[RFC6458] Stewart, R., Tuexen, M., Poon, K., Lei, P., and V.
Yasevich, "Sockets API Extensions for the Stream Control
Transmission Protocol (SCTP)", RFC 6458, December 2011.

[I-D.ietf-6man-udpzero]

[RFC6936] Fairhurst, G. and M. Westerlund, "Applicability Statement
for the use Use of IPv6 UDP Datagrams with Zero Checksums",
draft-ietf-6man-udpzero-12 (work in progress), February
2013.

[I-D.ietf-behave-sctpnat]
Stewart, R., Tuexen, M., and I. Ruengeler, "Stream Control
Transmission Protocol (SCTP) Network Address Translation",
draft-ietf-behave-sctpnat-08 (work in progress), February
2013.

[I-D.ietf-tsvwg-natsupp]
Stewart, R., Tuexen, M., and I. Ruengeler, "Stream Control
Transmission Protocol (SCTP) Network Address Translation
Support", draft-ietf-tsvwg-natsupp-05 (work in progress),
February
RFC 6936, April 2013.

Authors' Addresses

Michael Tuexen
Muenster University of Applied Sciences
Stegerwaldstrasse 39
48565 Steinfurt
DE

Email:

EMail: tuexen@fh-muenster.de
Randall R. Stewart
Adara Networks
Chapin, SC 29036
US

Email:

EMail: randall@lakerest.net